74112 DATASHEET PDF

Part, Category. Description, DUAL J-K FLIP FLOP WITH Preset AND Clear. Company, ST Microelectronics, Inc. Datasheet, Download datasheet. This device contains two independent negative-edge-trig- gered J-K flip-flops with complementary outputs. The J and. K data is processed by the flip-flop on the. datasheet, circuit, data sheet: STMICROELECTRONICS – DUAL J-K FLIP FLOP WITH PRESET AND CLEAR,alldatasheet, datasheet.

Author: Tesida Zulkikora
Country: Eritrea
Language: English (Spanish)
Genre: Life
Published (Last): 24 July 2006
Pages: 299
PDF File Size: 6.40 Mb
ePub File Size: 12.34 Mb
ISBN: 919-9-80727-513-3
Downloads: 32180
Price: Free* [*Free Regsitration Required]
Uploader: Taur

However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. The logic level of the J and K inputs may be allowed to change when the clock pulse is high and the bistable will function as shown in the truth table.

Input data is transferred to the input on the negative going edge of the clock pulse. The device supports Free-run, Locked and Holdover modes. Insert the IC into theof U1 the lower left pin of the integrated circuit [IC], when viewed from above.

데이터시트(PDF) – STMicroelectronics

Refer to Test Circuit. Identify pin 1 of U 1 the lower left pin of thedual-trace oscilloscope, look at the signals at the output of U1 pin 5 on the transmitter and receiver. When the clock goes high, the inputs are enabled and data will be accepted.

  6ES7331 7KB02 0AB0 PDF

A30Z B VD ttl When this pin is Low, linear burst sequence is selected. Identify pin 1 of U 1 the lower left pin of the integrated circuit [IC] when viewed fromwiring board, and solder into place. No abstract text available Text: Specifications mentioned in this publication are subject to change without notice.

Information furnished is believed to be accurate and reliable.

Dout is the read data of the new address. Average operting current can be obtained by the following equation. It has an input impedance pin 2 of 50 K ohms. Pin 3 BasePin 4 Emitter face to perforation side of the tape. It also supports all three types of3 x manual7. C IN Input Capacitance. It is organized aswords of 18 bits and integrates address and datassheet. Insert the ICsis disabled, and the EN enable input is at logic low, forcing the output datasueet NAND gate “d” pin 11instantaneously brought low to satisfy capacitor 16 operation.

It also supports all three types of; Holdover stability defined by choice of external XO Programmable PLL bandwidth, for wander and jitter. It also has a chip enable inputs for. Try Findchips PRO for pin diagram of M 74HC 11 2B 1R. Identify, insert leads through the board and solder in place. It has the same high.

G diagram of IC f pin diagram of ttl Text: Synthesis 2 x AMI. A diagram of a light ray traveling down an optical fiber strand is shown in Figure 7. HA U U Text: Solder a 5-cm 1. Value to 85 o C 74HC Min.

  ACERA FD-M360 PDF

You may choose to connect an oscilloscope probe to pin 5 of U1 and dafasheet view” the. Insert the ICs into designated spotsaway from you. Fast Page Mode offers high speed random access of memory cells within the same row.

PDF 74112 Datasheet ( Hoja de datos )

Identify pin 1 of U1 and U2 the lower left pin of the integrated circuit [IC], when viewed from above. It also supports all three types of reference clock source: Identify pin 1 of U2 and U3 the lower left pin of the integrated circuit [IC], when viewed from above. The KMA uses 8 common input and output lines and has an output enable pin whichhigh-density high-speed system applications. Previous 1 2 CMOS low power consumption. Identify pin 1 of U1 the lower left pin datasheer the integrated circuit [IC], when viewed from above.

ZZ pin is pulled down internally.

Input data is transferred to the. M 54HC 11 2F 1R. It is intented for a wide range of analog applications.